Vote

Basic parameter for domestic fan selection

Keep up with us

RSS Subscribe to blog
Vents.TV

Blog messages

Go to blog

AVU 03/SE/R/ОH

AVU 03/SE/R/ОH

Air handling unit with a rotary regenerator. Maximum capacity - 3000 m3/h.

Products in this series  (3)

  • AVU 03/SE/R

    AVU 03/SE/R

    AVU 03/SE/R/H

    AVU 03/SE/R/H

    AVU 03/SE/R/О

    AVU 03/SE/R/О


ParameterValueUnit
Phase
3
˜
Unit voltage
400
V
Frequency
50
Hz
Maximum unit power
2520
W
Maximum unit current
4
A
Maximum air capacity
3000
1767
834
0,834
50100
m³/h
CFM
l/s
m³/s
l/m
Casing material
aluzinc
Maximum transported air temperature
-25 +60
оC
Insulation
50 mm, mineral wool
Connected air duct size
600х350
mm
Filter: extract
panel filter G4
Filter: supply
panel filter G4 and bag type F7
Heat recovery efficiency
65
up to %
Heat exchanger material
aluminium
Heat recovery
yes
Water cooler block (not included delivery)
C3/AVU 03/О
DX cooler block (not included delivery)
DX3/AVU 03/О

E-mail

Please, feel free to contact us.

support@vents.ua

Phohe

Customer service.

+380 44 406 36 25

Online form

Send a message center customer support.


By using this form you confirm that you have read and agree with the site condition and terms.
Send

Water heater parameters:


Water heater parameters calculation example:
Air Speed. Starting from 3500 m3/h on the air flow scale draw a vertical line 1 till the air speed axis which makes 4.65 m/s..

  • Supply air temperature. Prolong the line 1 of air flow up to the point where it crosses the outside air temperature (-10°C); then draw a horizontal line 2  from this point to the left till crossing water in/out temperature curve (90/70). From this point draw a vertical line 3 to the supply air temperature axis on top of the graphic (+22.5 °C).
  • Heating capacity. Prolong the line 1 up to the point where it crosses the outside air temperature (red line, -10°C) and draw a horizontal line  4 from this point to the right until it crosses water in/out temperature curve (90/70), from here draw a vertical line 5 up to the scale representing the heating coil capacity (42.0 kW).
  • Water flow. Prolong the line down to water flow axis at the bottom of the graphic 6 (0.5 l/s).
  • Water pressure drop. Draw the line 7 from the point where line 6 crosses the black curve to the pressure drop axis. (6.5 kPa).

 

Water cooler parameters:


Water cooler parameters calculation example:
Air Speed. Starting from 2850 m3/h on the air flow scale draw a vertical line 1 till the air speed axis which makes 3.85 m/s.

  • Supply air temperature. Prolong the line 1 of air flow up to the point where it crosses the outside summer air temperature (+32°C); then draw a horizontal line 2 from this point to the left till crossing intake air humidity curve (50%). From this point draw a vertical line 3 to the air temperature downstream of the cooler axis on top of the graphic (+20.7 °C).
  • Cooling capacity. Prolong the line 1 up to the point where it crosses the summer outside air temperature (+32°C) and draw a horizontal line 4 from this point to the right till crossing intake air humidity curve (50%), from here draw a vertical line 5 up to the scale representing the cooling coil capacity (19.8 kW).
  • Water flow. Prolong the perpendicular line down to water flow axis at the bottom of the graphic 6 (0.78 l/s).
  • Water pressure drop. Draw the line 7 rightwards from the point where the line 6 crosses the curve to the pressure drop axis. (30 kPa).

 

DX cooler parameters calculation example:


DX cooler parameters calculation example:
Air Speed. Starting from 3500 m3/h on the air flow scale draw a vertical line 1 till the air speed axis which makes 4.65 m/s.

  • Supply air temperature. Prolong the line 1 of air flow up to the point where it crosses the outside summer air temperature (+30°C); then draw a horizontal line 2 from this point to the left till crossing intake air humidity curve (50%). From this point draw a vertical line 3 to the air temperature downstream of the cooler axis on top of the graphic (+22.5 °C).
  • Cooling capacity. Prolong the line 1 up to the point where it crosses the summer outside air temperature (+30°C) and draw a horizontal line 4 from this point to the right till crossing intake air humidity curve (50%), from here draw a vertical line 5 up to the scale representing the cooling coil capacity (14.5 kW).
  • Coolant flow. Prolong the perpendicular line down to coolant flow axis at the bottom of the graphic 6 (310 kg/hr).
  • Coolant pressure drop. Draw the perpendicular line 7 rightwards from the point where the line 6 crosses the curve to the pressure drop axis. (24.0 kPa).