Heat recovery ventilation unit VENTS MICRA 80 A3

Description
Characteristics
Downloads
Dimensions
Dimensions
Accessories
Ventilation system arrangement

Description

FEATURES

Efficient supply and exhaust ventilation of separate premises (rooms).
Enthalpy cross-flow heat exchanger with heat recovery efficiency from 68 % up to 77 %.
Centrifugal fans with forward curved blades.
Asynchronous motors with ball bearings. Integrated control system with three operation modes and air flow range from 40 up to 80 m³/h.

Silent operation (24/32/41 dBA).
Air filtration with two integrated G4 filters.
Easy installation.
Suitable for continuous operation.

OPERATING LOGIC

Fresh intake air from outside moves through the filter and the heat exchanger and is delivered to the premise with the supply fan.
Warm stale air moves from the room through the filter and the heat exchanger and then is exhausted outside with the exhaust fan.
Heat energy of warm extract air is transferred to clean intake air and warms it up.
Heat recovery minimizes thermal energy losses and space heating expenses in cold seasons.
Intake and extract air flows are fully separated within the heat exchangers and pollutants, odours and microbes contained in extract air are not transmitted to supply air.

CONTROL AND AUTOMATION

The unit is operated with a three-position speed switch.
The control system enables three operation modes:

Supply and exhaust ventilation with minimum air flow rate of 40 m³/h and noise level of 24 dBA.
Supply and exhaust ventilation with medium air flow rate of 60 m³/h and noise level of 32 dBA.
Supply and exhaust ventilation with maximum air flow rate of 80 m³/h and noise level of 41 dBA.

А3: three-position speed switch (P3-1-300)

Characteristics

Parameter	MICRA 80 A3 Speed 1	MICRA 80 A3 Speed 2	MICRA 80 A3 Speed 3	Measurement unit
Speed	1	2	3	-
Phase	1	1	1	˜
Frequency	50	50	50	Hz
Voltage	230	230	230	V
Power	25	35	57	W
Noise level	24	32	41	dBА
Air capacity	40	60	80	m³/h
Current	0.15	0.20	0.34	A
Filter: extract	G4	G4	G4	-
Transported air temperature	-25...+40	-25...+40	-25...+40	°С
Filter: intake	G4	G4	G4	-
Heat recovery efficiency	68...77	68...77	68...77	-
Weight	17	17	17	kg
Heating	without heating	without heating	without heating	-
Casing material	polymer coated steel	polymer coated steel	polymer coated steel	-
Remote control panel	Mechanical	Mechanical	Mechanical	-
Insulation	15 mm, polyethylene foam	15 mm, polyethylene foam	15 mm, polyethylene foam	-
Heat exchanger type	cross-flow	cross-flow	cross-flow	-
Heat exchanger material	enthalpy	enthalpy	enthalpy	-
Duct	125	125	125	-

Files archieve

Downloads

Dimensions

Characteristics

Parameter	Value	Measurement unit

Dimensions

Accessories


Round Ø 125 mm telescopic air duct, adjustable length from 500 up to 1000 mm		MVM 122 bVs N stainless steel outer hood		SF 195х195х6 G4 filter

Ventilation system arrangement

One MICRA 80 A3 air handling unit should be installed in each space requiring ventilation. A single unit is capable of ensuring efficient ventilation in spaces with floor area up to 32 m².	A ventilation system based on MICRA 80 A3 is able to provide continuous air exchange and save heat in winter and cool in summer.

Mark the holes for the air ducts on the wall with the supplied cardboard master plate. After drilling the holes fix the master plate to the wall with a mounting tape. Insert the 125 mm plastic air ducts in the core holes. The master plate is used to place the air ducts in a required position and to align the unit spigots with the air ducts. Install the outdoor ventilation hoods from outside to prevent ingress of water and foreign objects inside the unit. Install the air ducts slightly sloped down to outside to ensure condensate drainage from the unit. After the air ducts are fixed in required position using the outer ventilation hoods and the master plate fill the gaps between the air ducts and the wall with a mounting foam through the special slots in the master plate. After the mounting foam hardens, remove the master plate and cut protruding parts of the air ducts to be flush with wall surface. To mount the unit casing, open the service panel and take off the heat exchanger. Connect the unit spigots to the plastic air ducts and fix the unit casing to the wall with screws and dowels. After completion of the casing mounting and wiring operations re-install the heat exchanger and the front panel.